#Engrave a photo on laser cut 6.1 manual
#Engrave a photo on laser cut 6.1 archive

#Engrave a photo on laser cut 6.1 archive

Simply unpack the archive in any desired location on your HDD and you are ready to use the application. The setup is a swift and straightforward process that does not take too much time and does not require any special attention from your part. Quick installation and user-friendly interface In case you invested in a DIY Laser Engraver, then you can take advantage of tools like LaserGRBL to customize your favorite items with a prime marking. Long-lasting and appealing, laser marking constitutes an excellent way to add a personal message on a piece of jewelry, devices, electronics, musical instruments and even firearms.

Add Telegram Notification via LaserGRBL bot.

#Engrave a photo on laser cut 6.1 manual

The manual for the laser cutter is in the Dream Chamber.What's new in Laser GRBL 4.6.1 Pre-release: Please read the user manual for the meaning of the PPI and Air. For cutting other thickness / other materials, the speed and power parameter have to be changed accordingly. Speed of 2 and power of 90 is a parameter we tested that will be strong enough to cut through the 5mm acrylic board. The above configuration sets the green color in the drawing as vector cutting.

Speed: 2, Power: 90, PPI: 1200, Raster: NO, Vector: YES, Air: YES, other leave as default.

(represented by green color) with the following parameters: Please observe and understand the difference between raster engraving and vector engraving later when we start the cutting. Speed of 25 and power of 20 is a parameter we tested that will only engrave the 5mm acrylic board but not cutting through it. The above configuration sets the red color in the drawing as vector engraving.

Speed: 20,В Power: 25, PPI: 400, Raster: NO,В Vector: YES,В Air: YES, other leave as default.Set the Pen No 2.(represented by red color) with the following parameters:.Whether we are cutting or engraving is mostly determined by the Speed and Power setting of the pen. The above configuration sets the black color in the drawing as raster engraving. Speed: 20,В Power: 20, PPI: 400, Raster: YES,В Vector: NO,В Air: YES, other leave as default.Set the Pen No 1.(represented by black color) with the following parameters:.Doing so will ensure the machine will operate effectively and safely over a long period of time. Regularly clean and maintain the machine according to the cleaning and maintenance instructions in Chapter 8 of the user manual.Do not laser heat-sensitive surfaces or materials that may generate toxic fumes, such as PVC and Teflon.An exhaust system is already installed in the Innovation Wing laser cutting room. Odors, vapors, and dust are by-products generated during the laser engraving and cutting process. Ensure the immediate work area of the machine is well-ventilated.Do not attempt to remove or modify any component of the machineвЂ™s laser interlock safety system.Do not attempt to modify or disassemble the laser module.Do not open the laser access panel when the machine is plugged in.Ensure the voltage of the power source is identical to the voltage of the machine. Connect the machine to a properly grounded power outlet.Severe eye damage may occur if proper safety goggles are not worn. Reflective materials such as mirrors, enameled brass, and anodized aluminum may partially-reflect some of the invisible laser radiation. Always wear safety goggles when the laser system is in operation.

Enable the SmartAIRв„ў nozzle when engraving or cutting materials that may easily ignite, such as acrylic, wood, or paper.Caution-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.A well-maintained fire extinguisher and operational smoke or fire detector should be kept in the vicinity of the machine. The laser may ignite combustible materials. Never leave the machine unattended during the laser cutting and engraving process.Prior to operation, carefully read and familiarize yourself with the warning labels located on both the laser system and in the user manual.Proper use and regular maintenance of this machine is important to the safety of all people in the immediate area. LASER RADIATION WARNING: Exposure to laser radiation may result in physical burns and severe eye damage.Always remove the vector grid to clean any small pieces that have fallen through the grid.

Always keep the machine clean after the job finished.

DO NOT leave debris and scraps inside the laser machine after the job finished.

The resulting debris from laser cutting is very dangerous and may cause a fire hazard.